|
|
发表于 2014-12-20 17:04:55
|
显示全部楼层
#Test
#NTP_SERVER=time.gpsonextra.net
#Asia
# NTP_SERVER=asia.pool.ntp.org
#Europe
# NTP_SERVER=europe.pool.ntp.org
#North America
#NTP_SERVER=north-america.pool.ntp.org
#This is LG240 original setting for gps
#NTP_SERVER=0.kr.pool.ntp.org
#XTRA_SERVER_1=http://xtra1.gpsonextra.net/xtra2.bin
#XTRA_SERVER_2=http://xtra2.gpsonextra.net/xtra2.bin
#XTRA_SERVER_3=http://xtra3.gpsonextra.net/xtra2.bin
#End of the original setting
NTP_SERVER=0.cn.pool.ntp.org
NTP_SERVER=1.cn.pool.ntp.org
NTP_SERVER=2.cn.pool.ntp.org
NTP_SERVER=3.cn.pool.ntp.org
NTP_SERVER=cn.pool.ntp.org
XTRA_SERVER_1=http://xtra2.gpsonextra.net/xtra.bin
XTRA_SERVER_2=http://xtra1.gpsonextra.net/xtra.bin
XTRA_SERVER_3=http://xtra3.gpsonextra.net/xtra.bin
SUPL_HOST=suplcn.sirf.com
SUPL_HOST=supl.google.com
SUPL_HOST=221.176.0.55
SUPL_PORT=7275
# DEBUG LEVELS: 0 - none, 1 - Error, 2 - Warning, 3 - Info
# 4 - Debug, 5 - Verbose
DEBUG_LEVEL = 5
# Intermediate position report, 1=enable, 0=disable
INTERMEDIATE_POS=0
# supl version 1.0
#SUPL_VER=0x10000
# supl version 2.0
SUPL_VER=0x20000
# Error Estimate
# _SET = 1
# _CLEAR = 0
ERR_ESTIMATE=0
# GPS Capabilities bit mask
# SCHEDULING = 1
# MSB = 2
# MSA = 4
# ON_DEMAND_TIME=0x10
# ULP = 0x20
# default = MSA | MSB | SCHEDULING | ULP
# CAPABILITIES=0x27 // Not support ULP
CAPABILITIES=0x17
# Accuracy threshold for intermediate positions
# less accurate positions are ignored, 0 for passing all positions
# ACCURACY_THRES=5000
################################
##### AGPS server settings #####
################################
# FOR SUPL SUPPORT, set the following
# SUPL_HOST=supl.host.com or IP
# SUPL_PORT=1234
#SUPL_HOST=supl.google.com
#SUPL_PORT=7276
POSITION_MODE=0
# FOR C2K PDE SUPPORT, set the following
# C2K_HOST=c2k.pde.com or IP
# C2K_PORT=1234
################################
# Sensor Settings
################################
# Needs to be set explicitly based on sensor
# There is no default value.
#GYRO_BIAS_RANDOM_WALK=
# Sensor Sampling Rate Parameters for Low-Data Rate Filter (should be greater than 0)
SENSOR_ACCEL_BATCHES_PER_SEC=2
SENSOR_ACCEL_SAMPLES_PER_BATCH=5
SENSOR_GYRO_BATCHES_PER_SEC=2
SENSOR_GYRO_SAMPLES_PER_BATCH=5
# Sensor Sampling Rate Parameters for High-Data Rate Filter (should be greater than 0)
SENSOR_ACCEL_BATCHES_PER_SEC_HIGH=4
SENSOR_ACCEL_SAMPLES_PER_BATCH_HIGH=25
SENSOR_GYRO_BATCHES_PER_SEC_HIGH=4
SENSOR_GYRO_SAMPLES_PER_BATCH_HIGH=25
# Sensor Control Mode (0=AUTO, 1=FORCE_ON)
SENSOR_CONTROL_MODE=0
# Enable or Disable Sensors for GPS use (0=Enable, 1=Disable)
SENSOR_USAGE=0
# Choose GSIFF sensor provider (1=DSPS, 2=Android NDK)
SENSOR_PROVIDER=1
################################
# Indoor Positioning Settings
################################
# 0: QUIPC disabled, 1: QUIPC enabled, 2: forced QUIPC only
QUIPC_ENABLED = 0
################################
# EXTRA SETTINGS
################################
# Enable or Disable Wiper (1=Enable, 0=Disable)
ENABLE_WIPER=0
####################################
# LTE Positioning Profile Settings
####################################
# 0: Enable RRLP on LTE(Default) 1: Enable LPP_User_Plane on LTE
LPP_PROFILE = 0
################################
# LGE EXTRA SETTINGS
################################
VENDOR=KT
LGE_TLS_MODE=0
LGE_GPS_POSITION_MODE=0
|
|
关注公众号
窥视卡
雷达卡
显身卡
